Central issue:
This article refers to the address: http://
Electromagnetic interference in automobiles
Characteristics of electromagnetic interference in automobiles
Engine ignition system produces interference conducted along the power line
Inductive load produces interference conducted along the power line
Electrostatic discharge interferes with electronic components in the car
When an engine powered by an ignition engine is running on the road, the high-pressure ignition system of the gasoline engine generates strong electromagnetic waves, interferes with the normal operation of the radio broadcasting and radio communication services around it, and pollutes the electromagnetic environment. Since then, people have listed electromagnetic pollution as one of the three major sources of pollution (emissions, noise, electromagnetic). The International Radio Organization began to study the sources of interference in this form of high-energy pulses and proposed measurement methods and limitations. At present, the control requirements for electromagnetic pollution have been included in the technical regulations of countries around the world. After years of technical specifications, the cars running on the market have basically achieved effective control of the ignition pulse electromagnetic noise.
However, with the continuous advancement and development of automotive technology, the large number of applications of automotive electronic and electrical equipment, the characteristics of automotive electromagnetic interference and its impact have also undergone tremendous changes. The source of electromagnetic interference generated by automobiles is not simply an ignition system. A variety of electronic and electrical equipment used in vehicles also generate electromagnetic interference.
The electromagnetic interference generated by the vehicle not only affects the radio equipment outside the vehicle, but also adversely affects various electronic components inside the vehicle. In the early days, people were generally concerned about the significant impact of vehicle electromagnetic interference on the electromagnetic environment. With effective governance, this effect has been controlled. In recent years, there have been many phenomena in vehicles that have a significant impact on the normal operation, safety and reliability of vehicles due to electromagnetic interference inside the vehicle, which has caused people's special attention. At present, people began to study the generation and influence of electromagnetic interference inside the vehicle and its control technology.
First, the electromagnetic interference phenomenon in the car
The sources of electromagnetic interference generated by automobiles are: high-voltage ignition systems; various inductive loads (such as motor-type electrical components); various switch components (such as flash relays); various electronic control unit ECUs; and even various lamps, radios, etc. . The interference generated by these components can cause interactions inside the car. Here are some of the actual phenomena that have occurred.
Phenomenon 1: A medium-to-high-end sedan with a high-performance ABS system. The prototype encountered a rainy day in a live test and started the wiper. At a certain speed, the ABS suddenly lost its effect.
Phenomenon 2: A certain type of domestically produced miniature car, its generator regulator often appears to be easily damaged by breakdown. It has been found that this damage is likely to occur when the wiper is working.
Analysis of the above two examples, the main cause of this phenomenon is the wiper. The wiper drive motor acts as an inductive load. When the power is cut off, a reverse current is generated and transmitted to the power supply system through the power line, thereby generating interference pulses in the power system. Some electronic components cannot work normally under such interference pulse conditions. It even caused damage.
Phenomenon 3: An airbag developed and produced in China suddenly detonated on the assembly line of a complete vehicle. After testing the electronic igniting controller of the airbag, it was found that it could not withstand the strong environmental electromagnetic field, and when there was electrostatic discharge, it would malfunction.
Second, the characteristics of electromagnetic interference in the car
The characteristics of the electromagnetic interference inside the vehicle are different from the interference of the vehicle to the outside. In-vehicle electromagnetic interference can be transmitted through various connection cables, and it can also be transmitted by means of coupling and space-assisted emission. Typical forms are: conduction interference along the power line; interference from human body electrostatic discharge to electronic components; interference energy through space radiation. The following is an analysis of the characteristics of some typical sources of interference.
Third, the engine ignition system generates interference along the power line
The circuit block diagram of the engine ignition system is shown in Figure 1. The sensor obtains the ignition signal Va, and the driving circuit generates an on-off pulse current Ib at the primary of the ignition coil, and the coil secondary generates a high-voltage pulse to discharge the spark plug to ignite the engine fuel mixture. When the primary loop of the coil changes, the primary winding generates a transient voltage, the secondary winding generates a high voltage to discharge the spark plug, and the residual energy forms high-frequency electromagnetic radiation into the space. The transient voltage in the primary loop is transmitted along the power line to the power system, interfering with the power system, producing a ripple voltage ΔV. As shown in Figure 2. Generally, the experimental results show that ΔV is 2 to 4V.
Various electronic control units used in automobiles require a stable power supply voltage for proper operation. When a voltage fluctuation (such as ΔV) occurs in the power supply system, it will affect the normal operation of the electronic module.
Fourth, the inductive load produces interference conducted along the power line
Various types of motors used in automobiles are inductive loads. Such as: wiper drive motor; car starter motor; heater motor. This type of load characteristic circuit is shown in Figure 3. When the power supply to the inductive load is suddenly cut off, a reverse transient voltage Vc is generated, as shown in FIG. The larger the initial energy storage of the coil, the faster the turn-off speed and the higher the transient overvoltage. The measured results show that Va is generally -100V to 300V; is is 0.2s to 0.5s.
Although this type of interference is not continuous, its transient voltage amplitude is quite large, and occasional occurrences can seriously affect or even damage electronic modules. The generator regulator breakdown damage described in the previous section is a serious consequence of this reverse transient voltage.
5. Interference of electrostatic discharge on electronic components in the car
The human body generates static electricity, especially in the northern part of China. The winter climate is dry and the human body is prone to static electricity. The human body static electricity will be released when it encounters some conductors. There is direct discharge, which people can't feel. When the static electricity is stored to a certain extent, it will be discharged through the air, and even a spark will be generated, and people will have a strong discharge feeling. This type of electrostatic discharge is inevitable when people use a car.
APPDU â… (without intelligent management)
APPDU1020-6 / APPDU1028-6. it is the first generation of APPDU products. The product is assembled according to the 19-inch 1U cabinet, adopts integrated modular power supply and management mode, is carefully designed and manufactured, has 1000M non-managed 16 / 24 port POE Switch function, and four optoelectronic cascaded communication ports. The total power of DC power supply is 450 W, the 5 / 6 bit PDU strong power board function, the total power 4 000 W, does not have the intelligent management and the environment monitoring function.
Features:
- Input: AC100 220V 50/60Hz
- Total power: 4000W
- Function: with the function of 1000M management 16 / 24 port POE switch.
- Environmental monitoring: two temperature and humidity monitoring ports, one smoke sensing port, one device cascade port ,
- PDU function: comes with 5 / 6 bit smart PDU strong power plug board
- System: with background control system
Application :
Steady intelligent power supply management needs to monitor the electric equipment in real time, including the reading and analysis of the current, voltage and so on, so that the power supply can be turned off, the power can be restarted, the remote operation can be carried out, and the scientific management of electricity consumption can be realized. Realizing comprehensive energy saving. It Widely used in banks, offices, buildings, office buildings, garden communities, squares, factories, prisons, road traffic, gas stations, ships and other machine room heavy, power failure self-lock, can be embedded in the back-end security system
Product images:
APPDU â… (without Intelligent Management)
Intelligent Management System(Appdu),Appduâ… (Without Intelligent Management)
Dongguan Xiaoerduo Electronics Co., Ltd. , https://www.steadysmps.com