Abstract: This is an earlier applicaTIon note discussing the characterisTIcs and capabiliTIes of the DS1020, DS1021, and DS1045 programmable delay lines from Dallas Semiconductor. It discusses the architecture and funcTIonality of the two programmable delay line families: The single delay DS1020 / DS1021 / DS1023 and the dual delay line DS1045. Delay characteristics required by the design engineer such as linearity and effects of temperature are also discussed.
IntroductionThe system timing and control family includes programmable delay lines. These devices offer the user the ability to program the required delay after installation in the application rather than use factory-trimmed fixed-delay intervals. Economic considerations usually dictate that this approach is used whenever dynamic delay adjustment is needed in the system, rather than as a convenience to avoid specifying particular fixed delay values.
Figure 1.
DS1020 / DS1021 / DS1023 8-Bit Programmable Silicon Delay Lines These devices can be used in many of the same configurations illustrated here when dynamic alteration of system parameters is needed. The DS1020, DS1021, and DS1023 offer both parallel and serial methods of programming. In the parallel mode, an eight-bit word applied directly to a multiplexer, which selects the delay time desired. These values ​​may also be set via a three-wire serial bus.
The DS1020 is a single 8-bit programmable delay line with a choice of serial or parallel programming. Step sizes of 0.15ns, 0.25ns, 0.5ns, 1ns, and 2ns are available. The DS1021 is a similar, but lower-cost, device. It is offered only in SO packaging, with step sizes of 0.25ns or 0.5ns only. The DS1023 is a more fully-featured device than the DS1020 and DS1021. It has a inherent step zero delay time of 16.5ns, with steps sizes of 0.25ns, 0.5ns, 1ns, 2ns, and 5ns. In addition to the standard features, it includes a step-one reference delay output, a pulse-width modulator output option, and an inverted output option. It is constructed using a different topology that allows delay times greater than the pulse width.
DS1045 4-Bit Dual Programmable Delay LineThe DS1045 is effectively a 4-bit programmable delay line with two simultaneous programmable outputs from a single input. This device is particularly useful for skew adjustments as it allows either output to lead or lag the other.
Figure 2.
Internally, it is equivalent to a 16-tap delay line with two multiplexers for selecting which taps are routed to the outputs. Each multiplexer has a 4-bit parallel input to select the required tap, so one byte of data could fully program the device .
In addition to the data sheet, there is additional characterization of this device in Application Note 421, Device Characteristics of the DS1045 Dual 4-Bit Programmable Delay Line.
IntroductionThe system timing and control family includes programmable delay lines. These devices offer the user the ability to program the required delay after installation in the application rather than use factory-trimmed fixed-delay intervals. Economic considerations usually dictate that this approach is used whenever dynamic delay adjustment is needed in the system, rather than as a convenience to avoid specifying particular fixed delay values.
Figure 1.
DS1020 / DS1021 / DS1023 8-Bit Programmable Silicon Delay Lines These devices can be used in many of the same configurations illustrated here when dynamic alteration of system parameters is needed. The DS1020, DS1021, and DS1023 offer both parallel and serial methods of programming. In the parallel mode, an eight-bit word applied directly to a multiplexer, which selects the delay time desired. These values ​​may also be set via a three-wire serial bus.
The DS1020 is a single 8-bit programmable delay line with a choice of serial or parallel programming. Step sizes of 0.15ns, 0.25ns, 0.5ns, 1ns, and 2ns are available. The DS1021 is a similar, but lower-cost, device. It is offered only in SO packaging, with step sizes of 0.25ns or 0.5ns only. The DS1023 is a more fully-featured device than the DS1020 and DS1021. It has a inherent step zero delay time of 16.5ns, with steps sizes of 0.25ns, 0.5ns, 1ns, 2ns, and 5ns. In addition to the standard features, it includes a step-one reference delay output, a pulse-width modulator output option, and an inverted output option. It is constructed using a different topology that allows delay times greater than the pulse width.
DS1045 4-Bit Dual Programmable Delay LineThe DS1045 is effectively a 4-bit programmable delay line with two simultaneous programmable outputs from a single input. This device is particularly useful for skew adjustments as it allows either output to lead or lag the other.
Figure 2.
Internally, it is equivalent to a 16-tap delay line with two multiplexers for selecting which taps are routed to the outputs. Each multiplexer has a 4-bit parallel input to select the required tap, so one byte of data could fully program the device .
In addition to the data sheet, there is additional characterization of this device in Application Note 421, Device Characteristics of the DS1045 Dual 4-Bit Programmable Delay Line.
These products do not need any power supply to be functioned. The entire range of power systems offered by us is manufactured with beat quality material in compliance with the well-defined industrial quality standards. These solar products suit well with the utmost needs of clients and can be customized as per their specifications and requirements. Our solar power systems comprise MNES specifications. The broad range of these products includes DC fans, portable lights, lighting systems, portable lanterns, CFL lamps, and other appliances.
20W 12Ah Solar Home Power,12Ah Solar Home Power,20W Solar Home Power
Yangzhou Bright Solar Solutions Co., Ltd. , https://www.solarlights.pl